EMC QLogic Guide d'installation Page 178
- Page / 216
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
178
EMC Host Connectivity with QLogic FC and iSCSI HBAs and FCoE CNAs for the Linux Environment
Configuring a Boot Device on an EMC Storage Array
The tarball contains the configuration files required to
configure the QLogic driver within the DD-kit development
environment. It contains the following files:
Makefile,
disk-info.qla4xxx,
modinfo.qla4xxx,
pcitable.qla4xxx,
and modules.dep.qla4xxx.
Obtain and configure a generic Red Hat Driver Diskette Development Kit
1. Download the current Device Driver Update Disk Development
Kit (
mod_devel_kit.tgz) from:
http://people.redhat.com/dledford/
2. Create a temp/ directory on your system. Copy the file
downloaded in step 1 into the newly created directory.
Untar the file using the following command:
[temp]# tar -xvzf mod_devel_kit.tgz
This creates a new directory named
mod_devel_kit. Read the
README and README.new_kernel_versions in the
mod_devel_kit directory before proceeding.
3. Set or uncomment the following variables in the top level
Makefile in the mod_devel_kit directory:
a.
DRIVER=scsi (This specifies that you are building a SCSI
driver)
Please verify that all other
DRIVER variables are commented
out. This is done by placing a # symbol on the desired lines to
be commented out.
b. Set the kernel version to the version you wish to build the
DD_kit.
Please verify that all other kernel versions are commented out.
For example for RHEL3.0, kernel version 2.4.21-32.EL:
RHEL3_KERNEL_DIRS=2.4.21-32.EL
4. Import the kernel tree for which you want to build the DD_kit.
This should import the whole kernel sources including the
*.c
and
*.h files. Execute the following command in the
mod_devel_kit directory:
For example for kernel version v2.4.21-32.EL:
- -508-435-1000 1
- Contents 3
- QLogic Driver 4
- Chapter 8 Additional Notes 6
- ◆ Linux operating environment 11
- ◆ QLogic adapters and drivers 11
- Courier italic 13
- Introduction 15
- Purpose of this document 16
- Host connectivity 16
- Boot device support 18
- FC and FCoE 19
- Zoning example 20
- Installation Steps 21
- Linux distribution of choice 23
- Summary of installation steps 24
- Support Matrix 25
- Installing the adapter 27
- Adapter edge connectors 30
- PCI Express slots 31
- PCI Express slots aligned 31
- Installing and Configuring 35
- Qlogic Corporation 36
- Upgrading the adapter BIOS 37
- ◆ “iSCSI HBAs” on page 42 39
- 0 for Loop Only 41
- 1 for Point-to-Point 41
- 3. Reboot the system 58
- is as follows: 69
- module is as follows: 87
- ◆ All I/O must be stopped 108
- Example: 127
- 5. Reboot the host 127
- Updating the 129
- CEE/Menlo or iSCSI 129
- Firmware 129
- Connecting to the 133
- Planning procedure 134
- Connecting to the Storage 135
- Port Alias: 138
- 3. Click Next 143
- 7. Click Done 145
- 6. Click Yes 148
- 8. Click Yes 150
- Configuring a Boot 151
- Device on an EMC 151
- Storage Array 151
- Limitations 155
- Preparing the host 158
- LUN is 000 164
- Do you have a driver disk 165
- Driver Update OK 166
- 18. Reboot the host 171
- <driver-version> 179
- Upgrading the kernel 183
- 19. Reboot the host 187
- Additional Notes 193
- Rebooting the host 196
- /lib/modules 197
- Solution Enabler) 202
- /dev/sd ln 206
- HPQ server-specific note 207
- Setting Up External Boot 209
- HS40 (8839) 209
- F1 to enter the server BIOS 210
- Enter. This boot 210
- Special Instructions 211
- SANsurfer 32, 126, 131 216
Produits connexes et manuels pour Mise en réseau EMC QLogic
Mise en réseau EMC QLogic Guide d'installation
(150 pages)
(150 pages)
Feiss P1320 manuali
Manuali dei proprietari e guide per l'utente per Illuminazione Feiss P1320.
We fornisce 1 manuali pdf Feiss P1320 per scaricare gratuitamente in base al tipo di documento: Manuale Utente
Commentaires sur ces manuels